Chinese translation for "cavity dimension"
|
- 模腔尺寸
Related Translations:
- Example Sentences:
| 1. | Fluid power exclusion devices inch series , cavity dimensions for
液动专用装置的空腔尺寸 | | 2. | The multi - object optimal design for cavity dimensions of precise mould
精密型腔模具成型尺寸的多目标优化 | | 3. | The researches show that the probability method for calculating the cavity dimension of injection mold is more reasonable than the extreme calculation method which is widely adapted now
研究表明，概率法计算注塑模成型零件工作尺寸比广为采用的极值计算法更为合理。 | | 4. | A new method for calculating the cavity dimensions of the injection mould for plastic gears , namely , modulus - varying method , was put forward . and two typical processing technologies were introduced
提出了一种计算塑料齿轮注射模型腔尺寸的新方法，即变模数法，并介绍了两种典型的加工工艺。 | | 5. | The influence of the injection pressure to the mold cavity thickness was analyzed , formulas of circular mold cavity thickness were calculated , providing theory basis for deciding the mold cavity dimension rightly
摘要分析了注射压力对模具型腔壁厚的影响，推导了圆形型腔壁厚的计算公式，为合理确定注射模具型腔壁厚提供了理论依据。 | | 6. | The couplers of accelerator structures are important components of electron knear . the efficient delivery of power from rf sources to accelerator structures depends crucially on the coupler cavity . the input coupler cavity is to be well matched , that is to say , it must have proper coupiing . and it must be tuned to the synchronous frequency . in this way , we can obtain the maximum power . in the past , the decision of the coupler cavity dimensions is very difficult
加速结构的输入耦合腔是电子直线加速器的重要组成部分。功率从功率源输送到加速管中，就依赖于输入耦合腔。输入耦合腔在整个结构中必须有良好的匹配即有恰当的耦合度，还必须工作在谐振频率。 | | 7. | Then in this article resonance method is adopted . the paper analyzes the usual measurement methods of complex permittivity , then analyzes and chooses te0np circular cavity based on the methods of the te01n high - q circular cavity , uses the mode purifying and cavity dimension optimizing techniques . the resonant frequencies of varies modes in the resonant cavity have been drawn by using matlab software , which makes our work more rapid and convenient
本文首先分析了复介电常数的常用测试方法,然后分析并选用了基于高q腔法原理的te0np圆柱腔,应用模式净化和腔体优化技术,利用matlab这一运算性能强大的工具软件编程,作出谐振腔中各个模式的频率分布图,使系统的设计工作清晰、便捷。 | | 8. | Abstract : a probability calculation formula used for the cavity dimension of injection mold is derived on the basis of analysing the variation rule of plastic shrinkage rate , and a quantitative relation among the variation of plastic shrinkage rate , plastics dimension tole - rance , manufacturing tolerance and wear allowance is discussed
文摘:在分析塑料收缩率波动规律的基础上，导出了注塑模成型零件工作尺寸的概率计算公式，讨论了塑料收缩率波动范围、塑件尺寸公差、制造公差以及修模裕磨量之间的关系。 |
- Similar Words：
- "cavity depth" Chinese translation, "cavity detached inception" Chinese translation, "cavity development" Chinese translation, "cavity die" Chinese translation, "cavity diffusion length" Chinese translation, "cavity diode" Chinese translation, "cavity disinfection" Chinese translation, "cavity dislocation" Chinese translation, "cavity drag" Chinese translation, "cavity drainage" Chinese translation
|
|
|
